Audi 80/Avant (B4)

Since 1991-1995 of release

Repair and car operation



Audi 80/Avant
+ The description
+ Engines
+ System of release of the fulfilled gases
+ Cooling system
+ Fuel tank and the fuel pump
+ The air filter and воздухозаборные channels
+ Injection system
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Antiblocking system of brakes
+ Wheels and tyres
+ Kuzovnaja electrosystem
+ Ignition system
+ Illumination
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
   Forward bumpers
   Forward part of the car
   Cowl
   Wings
   Молдинги
   Doors
   External rear-view mirrors
   The forward and back has flown down
   Cover of a luggage carrier at a sedan
   Back door of the versatile person
   Back bumper
   The sdvizhnoj hatch
   Procleaning of apertures for a water drain
   The control of anticorrosive protection of the bottom of a body
   Salon
   Seats
+ Search of malfunctions
+ Specifications



Back door of the versatile person

Drive of the lock of a back door of the version the versatile person

1 – the lock cylinder;
2 – a drive of the handle of a back door;

3 – connecting draughts;
4 – the lock.


For regulation of a back door from within the car it is necessary to insert between the lock and a lock plate распорную a plate in the thickness of 3 mm (in drawing it is allocated by red colour).

Removal

 PERFORMANCE ORDER

  1. To remove a covering of a back door.
  2. To disconnect or remove electric plug connections, a hose of system of locks with the central management and a hose to a back atomizer стеклоомывателя.
  3. To open a back door and to prop up it.
  4. To wring out pneumatic springs from the top spherical pins (on a door).
  5. To turn off шестигранные bolts above on a door loop. Two assistants should hold a door at the left and on the right.
  6. At installation to replace sealing washers between a loop and a door of a luggage compartment.
  7. To adjust the adjusting buffer of a back cover so that at the closed door between the buffer and a body there was a distance of 2-4 mm.

Removal of the cylinder of the lock

Removal of the cylinder of the lock occurs identically with described in section «Removal of the lock of a luggage compartment» for a sedan.

Removal of a drive of the handle of a back door

The versatile person

 PERFORMANCE ORDER

  1. To remove a covering of a back door.
  2. To disconnect all connecting draughts from a handle drive.
  3. For this purpose to take aside lock скобы connecting bent for to locks.
  4. To turn out two шестигранных a bolt with nuts.
  5. To take out a handle drive.
  6. Installation: in the middle and in parallel to enter a drive of the handle from a luggage compartment through a rectangular aperture in the bottom external part of a door.
  7. The stopper and sealing lining with a groove should adjoin to the bottom external part of a door.
  8. To turn a handle drive until apertures through passage and fixing apertures in the bottom part of a door will coincide.
  9. To tighten a drive of the handle a washer and шестигранным a bolt (10 Н•м).
  10. Again to hang all connecting draughts and to adjust their length.
  11. Connecting bent for to the lock cylinder: to establish the deenergizing lever in position is opened".
  12. To remove back сдвижную the button in the middle of connecting draught so halves are freely inserted each other.
  13. In this position to fix one in other carving parts of halves of draught and to stop сдвижной the button.
  14. To adjust connecting bent for to locks of a back door – look the following section.

Removal of locks of a back door

The versatile person

 PERFORMANCE ORDER

  1. To remove an internal covering of a back door.
  2. To uncouple connecting draughts of locks, having taken aside lock скобы.
  3. In each lock to turn on two шестигранные nuts in a door frame.
  4. To take out the lock in a direction inside.
  5. Installation: slightly to tighten nuts of locks, to establish fastening points on the centre.
  6. A few to weaken locking скобу (a lock part below on a body).
  7. To close a back door.
  8. From within a luggage compartment to enclose распорную a plate (thickness of 3 mm) between the lock and locking скобой.
  9. To close the lock in the second lock groove and to expose a back door.
  10. To adjust and fix backlashes. The backlash between an upper edge of a bumper and a bottom edge of a back door should make 6,5—7,5 mm.
  11. To tighten шестигранные nuts.
  12. To remove распорную a plate; regulation of the lock of a back door is finished.
  13. Now it is necessary to establish length (built in) draught of a drive: to remove back сдвижную the button in the middle of both connecting draughts so that halves have been freely inserted one into another.
  14. Lock latch at an open back door to put in position "is closed" (the second lock groove).
  15. In this position to fix carving parts of halves of draught one in another and to stop сдвижной the button.